Zx Spectrum Vga Access

The 48K Spectrum only has composite. The 128K models provide separate TTL-level RGB signals (0V = black, +5V = full intensity) and composite sync on the edge connector. For a clean VGA conversion, use a 128K model or add a composite-to-RGB decoder (e.g., using a LM1881 sync separator). | Parameter | Value | Tolerance | |------------------|---------------------------|-------------| | Horizontal scan | 31.46875 kHz | ±500 Hz | | Vertical scan | 59.94 Hz | ±0.5% | | Pixel clock | 25.175 MHz | ±0.5% | | H-sync polarity | Negative | | | V-sync polarity | Negative | | | Active pixels | 640 | | | Active lines | 480 | |

| Region | Lines | |---------------|--------| | V-sync pulse | 2 | | Back porch | 33 | | Active video | 480 | | Front porch | 10 | | Total | 525 | zx spectrum vga

| Region | Pixels | Time @ 25.175 MHz | |---------------|--------|-------------------| | H-sync pulse | 96 | 3.81 µs | | Back porch | 48 | 1.91 µs | | Active video | 640 | 25.42 µs | | Front porch | 16 | 0.64 µs | | Total | 800 | 31.78 µs (31.47 kHz) | The 48K Spectrum only has composite

frame_ready = true;

// Pseudo-code for RP2040 frame buffer VGA converter uint8_t framebuffer[192][256]; // 8-bit color volatile bool frame_ready = false; void capture_frame() // Wait for VSYNC from Spectrum while(gpio_get(HSYNC_PIN)); for (int y=0; y<192; y++) for (int x=0; x<256; x++) // Sample RGB at ~7 MHz uint8_t r = gpio_get(R_PIN); uint8_t g = gpio_get(G_PIN); uint8_t b = gpio_get(B_PIN); framebuffer[y][x] = (r<<2) Direct connection to modern VGA monitors fails due

This document provides a complete blueprint for constructing a ZX Spectrum VGA adapter. Adjust as needed for specific Spectrum models and monitor compatibility.

Abstract The ZX Spectrum (1982) produces a composite video signal (PAL or NTSC) with non-standard timing. Direct connection to modern VGA monitors fails due to different sync polarities, scan rates, and voltage levels. This paper presents a practical, low-cost VGA interface using discrete logic and an inexpensive microcontroller. The design converts the Spectrum’s TTL-level video output to VGA-compatible RGBHV, handles the necessary scan rate conversion (50.0 Hz to 60 Hz vertical), and doubles the horizontal line count to meet VGA’s minimum 31.5 kHz horizontal scan rate. A complete circuit diagram, timing analysis, and construction notes are provided. 1. Introduction The ZX Spectrum outputs a 15.625 kHz horizontal scan (for 50 Hz PAL) or 15.75 kHz (60 Hz NTSC). VGA requires at least 31.5 kHz H-sync and 60 Hz V-sync. Direct connection damages monitors and produces no image. Therefore, a line-doubler and frame-rate converter is required. This design uses a fast SRAM frame buffer, a pixel clock generator, and a microcontroller (e.g., RP2040 or ATMega328) to read the Spectrum’s video memory and generate proper VGA timings. 2. ZX Spectrum Video Characteristics (48K / 128K model) | Parameter | PAL Spectrum | NTSC Spectrum | |------------------------|---------------------------|--------------------------| | Horizontal frequency | 15.625 kHz | 15.75 kHz | | Vertical frequency | 50.125 Hz | 60 Hz | | Active pixels (H) | 256 | 256 | | Active lines (V) | 192 | 192 | | Border area | 48 lines top/bottom, 48 pixels left/right (approx) | similarly | | Pixel clock | ~7.0 MHz (derived from CPU 3.5 MHz x2) | ~7.16 MHz | | Video output | Composite (UHF/modulated) + TTL RGB via edge connector (128K models) | same | | Sync | Negative-going, embedded in composite | same |